Showing posts with label turf grass. Show all posts
Showing posts with label turf grass. Show all posts

Will shredded Fall leaves harm my lawn?

Many landscapers (such as out trainers) have been doing LELE for a number of years - they would not be doing this process if the results damaged the turf quality the following year! (Read their testimonials.)

Scientific research concerning leaf mulching on turf has been compiled by LELE team and by folks at the Westchester Cornell Cooperative Extension offices.

What are some LELE Tips for Landscapers?

Some simple tips for effective and efficient mulch mowing from landscapers experienced with LELE practices in the field:

  • SLOW DOWN! Mulch mowing is different than grass mowing. (Slower speed allows finer leaf chop.)
  • Install mulching blades (e.g.; “Gator" blades or mower brand-specific blades) on mowers.
  • Close the mulch plate on the mower deck.
  • Keep your mower blades well-sharpened.
  • Mow grass high through the fall so that leaf shreds can settle between grass blades.
  • Adjust the blade height to 2.5-4 inches high. (You'll need to experiment to determine optimum setting for your mower and site turf conditions to maximize leaf chop and minimize throw from under the deck.)
  • Mulch when leaves are dry or semi-damp, whenever possible.
  • Take on no more than 2/3 or 3/4 of a deck's width of material at a time. (With a full deck's width, you may be making the machine work too hard, often resulting in the “toss” of some un-chopped leaves right out the front and sides of the mower deck - it's simply a case of too many leaves at a time for the mower.)
  • Face mower discharge to the work-to-be-done side for easy re-grind when necessary.
  • If required, multi-pass to shred leaves completely (around 1" square is target size).
  • On subsequent passes, use a criss-cross pattern over the lawn to minimize rutting.
  • With deep leaf piles, raise the front of the mower to "attack" into the pile, then lower deck back down. Repeat this "raise & lower" chopping technique as required. (Hint: a counter weight on the rear of the deck helps reduce the effort to raise/tilt the chassis.)
  • Blow excess leaf shred on surface of turf across a wider lawn area to even out. Excess shred can also be blown into nearby landscape beds as a mulch.
  • Mulch mow collected leaves next to a target area where you desire to use the resulting mulch.
  • Learn the ROLLING CHOP technique to allow the mulcher man to work in concert with the man with the blower so that in a short time, everything is processed "in situ." (See details here.)

What is Grass-Cycling?

Grass-cycling simply refers to the process of leaving your grass clippings in place on your lawn as you mow. Since your mower is left in its "mulching" configuration, mowing both grass and fall leaves provides a 3-season solution to lawn care, while yielding all of the benefits discussed on this site (e.g.; time savings, cost savings, green house gas reductions, soil enhancement).

The average lawn produces 1,500 pounds of grass clippings - clippings from a 1,000 square foot lawn contribute 1/2 to 1 pound of nitrogen back into the soil. Clippings can provide up to 1/3 of the annual feeding requirements of your lawn. Clippings left in place can also help block weed germination.*

Note that according to Cornell recommendations, for best effect, grass should be mowed no lower than 3" to 3.5" and your mower blades should be kept sharp. If the grass is wet, several passes may be required to effectively (finely) mulch the cut blades. Done properly, grass-cycling will not create a buildup of thatch.

* From presentation on Backyard Conservation - Lawn Care Practices developed by the Ohio Federation of Soil and Water Conservation Districts. (Summary taken from slides 10 & 11. See also slides 12-14 for more discussion of leaf mulching.)  Read the entire presentation with speaker's notes (.pdf) on grass-cycling, leaf mulching, and water management in turf care. Also, be sure to get their 4 Simple Steps to Lawn Care.